Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Peter Hibbard

Pages: [1] 2 3 ... 5
1
General Discussion / Re: SSCA Melbourne GAM - CSY Breakfast
« on: November 10, 2018, 10:57:59 PM »
Hello Brett - I was not aware you were at the GAM?  If you are in the area then maybe we could get together on Sunday - tomorrow.  Dave and Trish from Equinox and Dave and Sherry from Soggy Paws are here.  There was talk about late tomorrow PM or dinner possibly.

Let us know...

Peter
 

2
General Discussion / Re: SSCA Melbourne GAM - CSY Breakfast
« on: November 08, 2018, 09:55:27 AM »
CSYERS - There has been a suggestion to modify where and when we get together at the GAM this year.  A suggestion has been made to change the venue from MEMAWS to SQUID LIPS RESTAURANT and to change from Sat AM to FRI PM after the seminars, music and cocktail party? Say around 6:30 PM.

What do you guys think?

Thanks...Peter

3
General Discussion / SSCA Melbourne GAM - CSY Breakfast
« on: November 01, 2018, 12:53:16 PM »
Hello all you CSYers! Hope many of you will be at the GAM  11/09-11/11/18 this year. We want to invite all to the annual CSY Breakfast at Memaws on Saturday 11/10 @ 7:30 AM.

MEMAWS - 600 E Eau Gallie Blvd, Satellite Beach, FL 32937
(321) 779-9670

I will place a sign up sheet on the bulletin board at the GAM entrance. If anyone needs a ride - let me know.

Peter and Jan - JAZZ
407-234-0396

4
Engines and Drive Train / Re: Exhaust Elbow - 4107 Westerbeke
« on: September 04, 2018, 09:11:55 AM »
Cleaned raw water system with Barnacle Buster concentrate 4:1.  Added to system until evidence of product exiting exhaust.  Let sit overnight and then flushed system.  Benefit result was 10'F lower in operating temp and increased raw water exiting exhaust. Did discover weak point in aluminum elbow in exhaust with small pin hole leaks. Replaced with all bronze set up and cleaned up connections etc. See pics below.

Thanks...Peter ..../).....

5
Engines and Drive Train / Re: Exhaust Elbow - 4107 Westerbeke
« on: August 27, 2018, 07:30:09 AM »
Matthew, Jules - thanks for the feedback - I will let you know how it goes.

Thanks...Peter

6
Engines and Drive Train / Exhaust Elbow - 4107 Westerbeke
« on: August 25, 2018, 12:43:10 PM »
Looking for others experience that have replaced their exhaust elbow.  Mine is wearing through with slight leak and needs to be replaced. I see there are Aluminum, Steel, Stainless Steel and even fiberglass options for materials available.  Any recommended sources for these?

Thanks...Peter..../).... 

7
Swap Meet / Re: Davits For Sale
« on: July 27, 2018, 10:10:27 AM »
Here is a pic of the davits.

8
Swap Meet / Stainless Steel Bimini frame for CSY 37
« on: June 12, 2018, 04:16:17 PM »
I removed my stainless steel Bimini frame from my CSY37 when I installed a new arch.  All stainless and in good condition. 

Make me an offer.

Thanks...Peter

9
Swap Meet / Davits For Sale
« on: June 12, 2018, 04:13:17 PM »
I have a set of Danforth Davits from my CSY37B I recently removed. 

Make me an offer.

Peter

10
General Discussion / Re: Afternoon Delight new owner
« on: June 05, 2018, 09:16:50 AM »
Beregina - glad to hear you have joined the CSY family. We have owned "JAZZ" a 37b 1978 #006 since 2007. If you have any questions concerning a 37 CSY I would be glad to help.

All the best.

Peter

11
Engines and Drive Train / Re: Cutlass bearing CSY 37
« on: April 07, 2018, 07:16:51 AM »
Ken, I replaced my cutlass bearing on my CSY37B 1978 and I also have a 1 1/4" shaft.  Mine was a 2" X 1 1/4" bearing.

Regards,

Peter
JAZZ

12
Hull and Rig / Re: Transparent hatches
« on: November 21, 2017, 08:10:32 PM »
Hatch Update - All hatches have been cut and an insert replaced with a "bronze" tinted 3/8" thick acrylic 19" X 19"sealed with butyl and stainless steel screws. There was a transition period to tighten and re-tighten the screws to seat the butyl and also to trim the butyl. Now all hatches are tight and leak free. A significant amount of light now enters the saloon, sleeping area and head.  To modify this entry during high sun, we snap on screens to help moderate this.

Thanks.....Peter

13
Hull and Rig / Winches - re-Chrome
« on: November 21, 2017, 07:46:58 PM »
I have some winches on my CSY 37B JAZZ where the chrome over brass is worn away pretty much and was thinking about re-chroming them. Has anyone done this? Any recommendations on vendors? Any idea on pricing? I am in Florida so in-state would be my first choice.

R&H Plating in Ft Lauderdale is a potential option from internet.

Any experience here would be apptreciated.

Thanks...Peter

14
General Discussion / Re: Melbourne Gam - CSY Breakfast
« on: November 13, 2017, 10:03:41 AM »
Hello CSY Family.  We had 15 people turn out for the CSY breakfast on Saturday 11/10/2017.  Lots of great stories and updates on folks projects and plans for cruising in the future. Thanks to all who attended.

If you missed it, then make sure it is in your plans plans for next year!

Regards,

Peter and Jan
SV JAZZ
CSY37B #006 1978

15
General Discussion / Melbourne Gam - CSY Breakfast
« on: November 10, 2017, 10:20:23 AM »
Hello all you CSYers! Hope many of you will be at the GAM 11/10-12/17 this year. We want to invite all to the annual CSY Breakfast at Memaws on Saturday @ 7:30 AM.

I will place a sign up sheet on the bulliten board at the GAM entrance. If anyone needs a ride - let me know.

Peter  and Jan - JAZZ
407-234-0396

Pages: [1] 2 3 ... 5